Contenu récent par fredi309

Try to load this calibration (it's for the Cactus)-> scroll down until you find it

No that's not possible, I think it's possible to deactivate it temporarly, but it will turn on again

Try to uncheck "new type obstacle detection system" in Zone 2133. Helped for me -> had the same issue best regards fredi309 from austria

The configuaration depends on the Paramaters in the NAC. I good Tip is to do a Backup from your old NAC and restore it on the new NAC. I recomend using VLUD's tool. You sure have a Wave3 in SD-variant which is OK !! best regards from austria

OK, I see :benetton: Then for me there are only 3 options 1: 2E210106F7FFFFFFFFFFFEFFFFFFFFFFFBFFFFFF7FFF7FFFFBFFFFEE38BEFF 2: 2E210106F7FFFFFFFFFFFEFFFFFFFFFFFBFFFFFF7FFF7FFFFBFFFFED38BEFF 3: 2E210106F7FFFFFFFFFFFEFFFFFFFFFFFBFFFFFF7FFF7FFFFBFFFFEC38BEFF Hope I'm alright now :voyons: I'll...

That's an amazing tool !!!-> Where can i get it ? If i understand it right I've to do an bitwise "XOR"-Conversion with my existing bytes and the mask :voyons:- in this case i would get the following result 0xFF "XOR" 0x03 -> would give "0xFC" (in offset 23) 0xBF "XOR" 0x80 -> would give...

Here is a full dump 62210006A29212BDFB210000000040FF000000A420200B8CE3FFE0A01004FF01 62210106F7FFFFFFFFFFFEFFFFFFFFFFFBFFFFFF7FFF7FFFFBFFFFEFB8BEFF 62F080982603708000039812786180FFFFFFFF1101FFFFFF01 62F0FE00000000039206031103071703FFFFFF0002000001927243 Thank you !!!

I've looked in all zones, but didn't find a concerning parameter :( best regards from austria PS.: I'm retrofitting front camera too at my 3008(P84) from 2018, if i find something out, I'll give feedback to you

Thanks for your great support !! I've done som Screenshots from my ESP unit (perhaps it helps to find the correct version) ESP-Zones Dump 6AD:222101 6AD:62210106F7FFFFFFFFFFFEFFFFFFFFFFFBFFFFFF7FFF7FFFFBFFFFEFB8BEFF 6AD:222100...

Is this a dump from your CAR ? That would make sense-> if you code it binary it would only change on Bit as shown below: EF->EE => 11101111->11101110; this could be for the activation of the Grip Control B8->38 => 10111000->00111000; this could be the BIt for the "Hill Descent Control" That...

Never, i had to change to "normal mode" everytime

The problem was, that ever when i put in the reverse gear, the camere has gone in "Zoom_Mode", and this was a problem auf wrong signals from the parking sensors ("red alert"). In real i was far away from any obstacle. It took me a lot of time to fix this issue. The final solution was the change...

@ jeery2212 Thanks a lot now the camera is working fine !! Meantime i solved the other issue with the "ever red parking sensors"-> !! The solution was to change the "type of obstacle detection system" to "old system"(unchecked the concering box).:) So all my problems concerning the wave4...

Hello from austria, I´ve just a short question: Which paramateres in ESP90 have to be changed to enable grip control !? I've found somethin in a previous post: 68D 6AD 2E:2101:28:EE 68D 6AD 2E:2101:29:7A Are the OK !? Thanks in advance for your help best regards fredi309

Hello from Austria i've found video which may help you -> see here