Contenu récent par MacSlavko

Strange that! In Portugal you should have full usage (7/7) of Connected Services. If the knob on the stalk works, then the only thing that comes to my mind now is that maybe for some reason NAC wasn't configured properly and needs another go with Arduino tool to enable the Voice commands...

Voice comands are not available in all the countries. For instance, they're only partly functional in Croatia. I'd say only the "local" services are available (handling the data stored on internal mamory, attached USB or on a connected phone), but "remote" services (that require connection to...

Yep. If you have your Arduino tool. You can set it up for half the token cost and use it without time or VIN limitations. Haven’t got around to set up mine yet…

Google translate: Tout ce dont vous avez besoin est un câble LVDS rond pour connecter le NAC au nouvel écran capacitif. Contrairement au RT6, le câble d'alimentation avec le connecteur marron dans le NAC n'est plus nécessaire...

"Almost the same VIN" wouldn't work for you because NAC has to be paired to your car's VIN which is written in BSI. That's why the seller needs to write your exact VIN into the NAC and it can't be changed later (unless you have your own Arduino tool to configure the NAC). As for the donor car...

Thought it does on-board Internet sharing? And when I go switching it on, NAC warns me that head unit will loose connection if I share it to the passengers… 2G/Edge still active in CRO.

Today i swapped my original BTA to BTA2.0 but still have no Internet!? After plugging in the 18-pin cable and connecting it with green USB cable to NAC (whout any telecoding) new BTA2.0 wouldn't give Internet to any device (to NAC or iPhone). I had full WiFi signal on NAC, but no Internet...

This is brilliant! Thanks for this info! That means I don't have to chase for BTA2.0 salvaged from a DS5 (quite rare and pricy) but I can take a BTA2.0 from any PSA vehicle (50-60€) and telecode it to my VIN and DS5 parameters! I just tested changing the language in existing BTA1.0 on my DS5...

So you installed BTA2.0, connected it to your NAC and it gave you the Internet connection needed for TomTom Connected services without even changing the BTA VIN (matching it to yours)? Was the BTA2.0 also from a (newer) Peugeot Expert, or from some other PSA vehicle? If I got you right, the...

How did you connect new BTA2.0 to the head unit? It uses USB cable (green port) to connect to NAC, whereas there's no such cable on BTA1.0. That may be causing "Communication error" shown in Diagbox...

Have you managed to change the VIN (and language, if needed) in your BTA2.0? You do that with Arduino tool? No errors in Diagbox anymore?

Thank you very much for your input and valuable information! Especially for the good news of Plug&Play for my new BTA2/3 project! :) Been looking up for damaged DS vehicles in my country, but for a year now the only one I could find was a prefecalift DS5 - so no BTA2 or 3! If I buy a used one...

Nice to see VLud here again! I've got one question regarding BTA2 that I can't figure out and kindly ask for help... My DS5 2015 came with BTA and SMEG+IV2. I swapped it with NAC Wave2 from a broken 2018 Peugeot Expert. It's Arguino configured and working fine. My exixting BTA is still working...

It works with iPhone as well, just the notification tab within the BT settings on the phone and then within the connected head unut (DS 5 in my case) have to be on! By default it(s not... I switched it on and those missing tabs for Messages and eMails apperead on the Phone settings of NAC head...

Yes, it's possible and you keep all the info regarding the hybrid (battery and stuff...) but all the settings must be telecoded right with Arduino tool so you need that well discussed with seller! Apart from the new screen, cable adapters and NAC telecoded to your car, depending on which car you...