Contenu récent par MasterDomino

Hahaha yes i know that im in fact searching for a little different mounting system that ill most likely model later, i also edited your bezel a bit so it fits a little bit differently, ill share those stls most likely today. What do you mean with can2004 settings? Is there an example config...

Alrighty, eveything works, sadly for my car as i had ng4 and didnt want to cut anything off i had to dump your mounting idea and just glue the display to the panel hahaha, its hot glue so its not permament and i can always remove it, now question is, how can i get back the settings for DRL and...

I dont understand, I have this plugged into the car, and after i turn the key, it displays everything and boots normally, just that it has the above mentioned problems, to calibrate i was using the psa-diag from you for bench calibration, this is the comfort can adapter that i have connected as...

oh wait is the modified one supposed to go to the Infotainment or the Car CAN Network, because i understood that the unmodified(lower one) should go to the Infotainment(NAC) how i understood it from the tuto, and yes i cannot change language nor i cant find where to change the time even(i killed...

Okay, sadly i cannot edit the last post anymore as well, so sorry for spam. those are my settings, sadly the radio still beeps, the BT still doesnt work even though the noFMUX is set to true, vins match, i guess it might be bad calibration of the unit, also is activation with diagbox...

okay, i didnt have 2.2k ohm so i did 4.7k in parallel which is about 2.2k, across CANL and CANH as thats how i understand it should be, but sadly the shield doesnt think its good and just lights up all leds and wont send anything to the unit(im using shield v1.2) i already tried different...

oh damn, i removed that resistor, i was swapping the damn shields because i thought i screwed something up, thank you very much oh my god, you just made my day, i got already scared that ill have to buy a second unit, ill get one more resistor then and will try doing a clean calibration this...

Hello again, Sadly i cannot edit this post anymore, i have went through with more stuff, seems like the tool is somehow unreliable and sometimes loses some bits(unless its my arduino setup that causes it) randomly dropping connection, I have successfully replaced the digitizer of the DGT7C...

Hello @VLud we finally managed to gather and start working with the NAC, after some troubleshotting we got it up and running, now the only thing i would like to ask about is if its possible to change the calibration and VIN with your arduino-psa-diag tool, i got to mention i got a beep every few...

what about displays mentioned in your thread over there: https://www.forum-peugeot.com/Forum/threads/tuto-remplacement-smeg-par-un-nac-wave2-sur-308-t9-bta-2-0.9539/ like for example 9824298580 from 309 T9 if i took it out of the plastic trim would those displays work as well? sizewise i guess...

Just to make sure 9812862880 display is meant for SMEG and wont work with Wave 4 yes? i need to find one of the references mentioned strictly as none other work?

Sorry, I meant the MATT COLOUR which you mounted, because some of them look interchangeable, also i noticed on stickers that part numbers for NAC Wave4 show Wave2.

Thank you very much for your quick answer, Would you be able to tell me the part numbers for both your wave3 and colour display? Or do those part number not really matter because all those parts look to me like they have the same mounting system, quite surprised peugeot left all this with same...

Hello VLud, I was planning on doing the same on my RCZ but instead using Wave4 which i found in poland for cheap(9835408780), i have a few questions: Do you think 8 inch would fit with modification to the fiasca panel or is 7 inch a better option? MATT COLOR you used does it need any...