Contenu récent par wdsmk

Various zones in BSI regarding the seat memory functions and pneumatic functions need to be changed. Also don't forget to telecode the BSI that now the car has pneumatic functions ECU and Memory ECU. Send me a PM and I can send a BSI config list from a C5 Aircross that has memory seats

That should be correct. I have Visiopark 1 Rear camera, front 4 and back 4 sensors, also automatic parking that only controls the steering. Works like a charm so far. Idk about the difference with 33 and 73 though.

My car has Park Assist activated (with driver intervention) It's enabled in AAS_UDS_G5 (2101BD) In BSI_2010_EV (230073) In DAE (61A005C0D80002000002) And in NAC (210CC010) I have not made any changes to ESP90 ECU; so in Diagbox I can see that CPK is not enabled. My question is, is it possible...

In multiplex system you can use AAS sounds from COM2008, in BSI zone 2302, set the zone to 01 Would you mind sharing about your DSP control system? I cant decide between have an analog amplifier or a DSP, with your control system I might be able to connect and control a DSP just like yours..

Actually you can turn off both DRLs from the touchscreen, I had to change some other zone information in order to make the DRL toggle in NAC to function properly. Can send you those if you want to. Regarding Sound Harmony, sadly I could not enable it. 23B4 is set to 01, same with the NAC but no...

W4, 8" (might be W3 in hardware but I'm quite sure it runs W4 software)

The answer lies in your question. UDS (ISO 14229-1) and KWP (ISO 14230) are two different automotive electronics communication protocols. You are not. KWP HAB uses 10C0 and KWP IS uses 81 for opening diagnostic session. UDS commands have a different layout and different measures to ensure...

When I telecoded AAS again but with secured traceability, it started working again so my guess is you don't have to worry about your AAS module becoming unusable or blocked. 34A0 000000 06 05 CC FD 000000 F8A7 34A0 > Request download to zone A0 00 00 00 > Memory address high, medium and low 06...

I wrote secured traceability for BSI and AAS. With NAC it's not necessary with Vlud's app and DAE uses KWP protocol.

Be careful, with my AAS_G5 I had to telecode it again with the secured traceability. Without it, the module turned itself off; parking sensors and blind spot detection stopped working.

I am trying to activate the menu in NAC which lets you change the warning, turn signal, seatbelt chimes etc.. Zone 23AB (COM2008 Sound Presence), if set to 01, changes these chimes with an older Peugeot variant. Someone recommended zone 23B4 and I enabled it. I still don't have the sound menu...

Is it possible for you to attach your Wave2 .nac file which includes your zone info? I would like to cross-reference it to my Wave4. I think I miss something essential about it. Also, the menu can be entirely missing because of a different calibration.

Greetings ygorigor, thank you for the insight. When 23AB is set to 01, the chimes change to an older variant (Peugeot 2012); However, when I set 23B4 to 01 and set 23AB to 00, I still cannot access/find the submenu which lets you change the chimes. I have a NAC Wave 4, BSI 2010_EV equipped on...

Greetings, I was able to enable Harmony sound from both NAC and BSI Zone 23AB. However, I am not able to select other warning sounds within the NAC. Have you enabled anything else in NAC? Thanks in advance. I can attach my NAC zone backup if needed.

Of course. I think Sound Harmony lets you select one of the few warning chimes (blinker and other warning chimes, seatbelt chime etc.) In VLud's BSI Zones document, it can be found as Zone 23AB "COM2008 Sound type presence". I set that zone to 01 which in turn changed my warning chimes from the...