[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

the beep is due to the wrong vin, you need to enter the vin of your car.
For the rear view camera you have to use a vin that mounts one, otherwise you have to use the vlud tool to do everything you need
 


Savez vous si Android Auto est disponible sur tous les RCC A2, ou pas?
Je sais que au début de la discussion c’était impossible a injecter une nouvelle calibration dans les RCC, mis je crois que la problème a était résolue depuis. Quelqu’un peut confirmer?
Merci
 



Salut! Je comprends beacoup de Francais mais parle petit peu Francais, donc je utiliser Anglais :ange:

First I think this is a great project, well done to Vlud and bagou91. I have built a Arduino based dash for my 307 (of 2006) using data from the CAN comfort bus but already thinking of all the newer things I could add also!

@VLud I am also working on the KWP and UDS protocols and extraction of commands for parameter measurements and actuator tests with Diagbox. It is good to find someone who also works on it. I have most of these data now, and am currently working on implementing the code to re-create "Global test"/Fault reading etc
 
  • J'aime
Reactions: levanid and marcins


@VLud I received my Arduino Uno and a 2.0 Can Bus Shield.
It wasn't working until i left untouched the PIN number 10 setting (CS_PIN_CAN0 10) instead of putting 9 as suggested (despite it was 2.0 version).
I was able to did some changes to my Corsa (like use different theme, the Opel one is terrible) and add some option like "Start and Stop" and Electric Brake management. Got really impressed with all the things you may do!
However my goal was to enable "handsfree opening" menu item that i miss on my NAC (despite I have the keyless entry). I tried to select it but it has no effect. I tried also the other "handsfree opening" item without luck.
Any suggestion?
Thank you so much
 

Pas certain de la compatibilité hardware du RCC / NAC Chinois avec Android Auto malheureusement

Buy an iPhone ? :lol:

Apres des tests je peux confirmer que le RCC/NAC Chinois este parfaitement compatible avec CarPlay mais malheureusement incompatible avec Android Auto.
 

Hi, Sorry i dont speak french so i write in english.

I followed the instructions however i only get 7f0000 when using the terminal.
What have i done wrong?

Many Thanks
 




heloo i am new to the forum and it is an honor to be here i wanted to ask if the arduino leonardo can-bus is an alternative with an obd2 to db9 cable that will work with the peugeot 3008 gt 2020 line for the telecoding?
 

Pièces jointes

  • Screenshot_20201122-235811_YouTube.jpg
    Screenshot_20201122-235811_YouTube.jpg
    626.2 Ko · Affichages: 77

Hi guys. Im trying this with Arduino Uno v3 and newest canshield v3.

Cant connect. If i use CS_PIN_CAN0 to 9, when i try to connect or send the test comands, nothing happens. If i use CS_PIN_CAN0 to 10, when i try the above, all 4 green lights Turn on but also nothing on the NAC unit and no messages Arduino software.

Any tip?
 

@lorddevereux Hey :) I'm also working on this as a bigger future project, we should work together

Bonjour a tous,
N’ayant toujours pas recu l’interface full ship, je me suis lancé avec la methode Arduino, et c’est du bonheur car tout c’est tres bien passé en suivant le tuto, encore une fois merci VLud et bagou91 pour votre boulot et le partage.
J’ai tout de meme une question VLud, peut on regler la hauteur de la camera de recul, on dirait que la vue est plus basse qu’avant, actuellement je vois une partie de la plaque d’immatriculation alors que qu’avant, je n’ai pas le souvenir qu’elle etait visible... A moins que c’est plutot un reglage droite gauche car le trait rouge n’est pas parallele au vehicule, et j’imagine que s’il devient parallele, on ne verra plus la plaque.
Y’a t’il une modification a faire via le menu « 212A »? Merci

upload_2020-11-26_10-49-2.jpeg
 

Bonjour @Misticrep
A mon avis c'est plus un réglage physique de la caméra à effectuer... tout du moins pour la partie droite-gauche.
Pour ma part, je vois également un bout du pare-choc avec ma 508 équipé d'origine.
 
  • J'aime
Reactions: Misticrep


Tu avais une caméra d'origine ?

Dans tous les cas, étant donné que la caméra est connectée au combiné, le menu Visiopark du NAC n'aura aucun effet (déjà qu'il n'a quasiment aucun effet en temps normal :D)
 

Bonjour @Misticrep
A mon avis c'est plus un réglage physique de la caméra à effectuer... tout du moins pour la partie droite-gauche.
Pour ma part, je vois également un bout du pare-choc avec ma 508 équipé d'origine.

Merci pour ta reponse rapide, j'ai essayé rapidement de bouger la camera de haut en baut et de droite a gauche, elle a l'air fixe, je n'ai pas forcé non plus, je regarderais ca plus en profondeur cet apres midi :)

@Misticrep It also depends on the type of system you have, if you have a 360 view then it is an instrument cluster configuration problem

Bonjour RuLe, j'y ai pencé et j'ai donc esszayé de changer de type de camera, de panoramique a 180° mais il n'y a aucun changement, tu as eu le meme probleme? si oui, quel changement as tu fait exactement? merci
 

Hi guys. Im trying this with Arduino Uno v3 and newest canshield v3.

Cant connect. If i use CS_PIN_CAN0 to 9, when i try to connect or send the test comands, nothing happens. If i use CS_PIN_CAN0 to 10, when i try the above, all 4 green lights Turn on but also nothing on the NAC unit and no messages Arduino software.

Any tip?

Where did you buy a "V3" ? If you are talking about the SunFlower CAN Shield V3 it is a cheap copy of the 1.2 with a 8Mhz Crystal, so you must keep CS_PIN 10 and change 16MHZ to 8MHZ
 

Hello.
Thank you @VLud for such an awesome tool
However I require your help as it seems there's a glitch
I have a DS4 (2014) with NAC Wave 3 (system version 42.01.72.32_NAC-r0) installed – everything was working great for almost 6 months

Few days ago I tried your tool (I've been using 1.1.5) to update settings of NAC (backup has been created before) and after applying something went wrong with top and bottom bars position on navigation screen (they are all become shifted at like 20px)
You could see it in photo below.
upload_2020-11-26_13-52-54.jpeg

I tried to restore backup but it didn't help. Configuration of NAC restores however menu position seems to be unaffected (it seems that tool erased some settings and in current version doesn't change menu XY position)

Can you please help me fix that
Here's calibration reference in case you might need that
upload_2020-11-26_13-55-43.jpeg
 
Dernière édition:

Tu avais une caméra d'origine ?

Dans tous les cas, étant donné que la caméra est connectée au combiné, le menu Visiopark du NAC n'aura aucun effet (déjà qu'il n'a quasiment aucun effet en temps normal :D)

Bonjour VLud,

oui c’est la camera d’origine, c’est bizard mais j’ai vraiment l’impression que je ne voyais pas le bout de plaque d’immatriculation avec le smeg... ou peut etre que j’y ai pas fait attention.

upload_2020-11-26_12-1-19.jpeg
 

@levanid : Wave3 NACs never have been installed on DS4, the tool is not erasing anything and a backup is restoring raw data directly.

Where you using the same theme before ? (because it seems related to that)
What is the origin of the NAC ?
What did you do with the soft exactly ?
 

@levanid : Wave3 NACs never have been installed on DS4, the tool is not erasing anything and a backup is restoring raw data directly.

Where you using the same theme before ? (because it seems related to that)
What is the origin of the NAC ?
What did you do with the soft exactly ?

Indeed it was a bit tricky to make it working, but all went good. NAC came from recent Citroen C4 Cactus
Your tool shows calibration 9693726480. However on your GitHub calibration for DS4 has different numbers DS4-9692638380.cal

Theme is the same I believe the name is Champagne - I have 4 of them available. If I enable 4 more themes (via your tool) they don't have names and do not apply

At first I wanted to just change bluetooth name as it contained extra characters like "BT_DS " (with 6-7 extra spaces) to just "DS4"
We also disabled A/C menu as it just shows the temperature but unable to change the values, I anyway have them available on DS4 dashboard below screen. Now NAC shows radio station on the top menu or currently playing song via BT

I believe main issue might come from "video resolution 1" and "video resolution 2" options. (I had them both disabled before) If I enable first option colours become corrupted, however the second option doesn't change anything

I want to also point that backup restoration doesn't help. All of the values being restored however menu is still broken :(
 
Dernière édition:

Where did you buy a "V3" ? If you are talking about the SunFlower CAN Shield V3 it is a cheap copy of the 1.2 with a 8Mhz Crystal, so you must keep CS_PIN 10 and change 16MHZ to 8MHZ

Yup Thats the One. Can you tell me how to Change to 8mhz? Ive read the tuto but maybe that part is being bad translated by Google. Im using the green 2 Wire connection
 



I'm not sure what you are meaning by fuel info, I would guess you talk about the "Onboard Computer" showing the remaining kilometers or the live fuel consumption.
 
  • J'aime
Reactions: Nosidefcp

[QUOTE = "VLud, post: 2591729, member: 108646"] I'm not sure what you are meaning by fuel info, I would guess you talk about the "Onboard Computer" showing the remaining kilometers or the live fuel consumption. [ / QUOTE]


Yes, fuel comsumption page like i had on the smeg unit.