[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

All the CIROCCO panels have the pin to receive the actual buttons to turn OFF/ON the ESP and its lights like the older dashboard. There is a parameter on telecoding to activate this pin and make the panel handle the request. But at least in the 3008 calibration i was not able to make it work. Its like the calibration lacks its support. At this time I recommend to leave at least the board of the old cluster installed to keep it working. Just sharing my experience.
Cirocco don't have pin for esp!!! Check schematic. I check for 508 and 3008 and don't have.
 
  • J'aime
Reactions: Miguel Angel


@Dravos It didn't disturb me at all but it's just annoying and useless to fill the discussion with things that have already been said

diagbox /Bsi configuration/vehicle configuration/lighting and signaling

or arduino

>752:652
1003
:E4D8:03:03 (this depend what type of bsi you have that's for bsi2010)

222407 read actual state

2E2407XX write where xx is the setting from diagbox 01/02/03/04/05 (2E is write new setting command)

Voir la pièce jointe 20288
 
Dernière édition:
  • J'aime
Reactions: Dravos


Without connecting the ESP button , esp still owrks :) ESP button is just to deactivate ESP for some period of time in normal cars and all the time in GTI until is turned on again with button or you restart engine again ...

At start ESP is fully functional and 98%ppl don't need to think about , i have GTi and need sometimes to deactivate it :) thats why im searching solution ..

parking sensor OFF/ONN can be set to work on NAC
tyre pressure initialization also can be set to work in NAC

the buttons without funcion can be wired to 2 push buttons on 3008 ciroccoto change ilumination and to ''check -display ''
 
  • J'aime
Reactions: hangway2

With arduino make a backup of the bsi configurations

I have performed some tests today. I don't know why, but if the SAM virtual switch is enabled in 2119 tab, NAC will show the ON/OFF switch, but it won't work. However, if the switch is enabled throug 2127 tab, it will be showed under Safety options and work.
Even if I have both enabled simultaneously, only the 2127 works.
I couldn't backup BSI parameters, as i don't know the steps to follow.
The attached pictures are exactly the current parameters in my NAC and SAM can be turned ON/OFF through it's virtual switch.
 

Pièces jointes

  • SAM_2.jpg
    SAM_2.jpg
    106.8 Ko · Affichages: 69
  • SAM_1.jpg
    SAM_1.jpg
    53 Ko · Affichages: 67

Without connecting the ESP button , esp still owrks :) ESP button is just to deactivate ESP for some period of time in normal cars and all the time in GTI until is turned on again with button or you restart engine again ...

At start ESP is fully functional and 98%ppl don't need to think about , i have GTi and need sometimes to deactivate it :) thats why im searching solution ..

parking sensor OFF/ONN can be set to work on NAC
tyre pressure initialization also can be set to work in NAC

the buttons without funcion can be wired to 2 push buttons on 3008 ciroccoto change ilumination and to ''check -display ''

Nice to know that I can "recycle" these switches, because I was wondering how to reallocate the brightness and maintenance switches from Cirocco. Just need to reuse the 2 boards, right?
 

I tried to enable video playback through USB stick, but couldn't find an option to do it.
I'm using a NAC Wave 4 SD with DAB.
I used the "search" function and filtered the results in this topic, other members already asked for it, but I didn't found the answer.

Anybody knows how to do it?

Thanks in advance.
 

When the official document says "track not connected" it is related to limitations on the vehicle you are viewing. For example when you search for the pins descriptions under C4 Gran Picasso it says "track not connected" to many other pins which are already described on this 3008 page. CIROCCO was used in a variety of cars such as 508 II, DS7, DS9, Chinese C5 and C6, 5008, Corsa etc. I can not tell exactly which pin needs to be triggered to turn ESP ON/OFF but is certainly one of those "not connected" pins which all CIROCCO have despite its calibration. I was planning to discover by myself once the telecoding was done but was not.
Btw, the parameter is called "CFG_EI2_CMB_WIRE_IN_ESP_PUSH_000".
 

CFG_EI2_CMB_WIRE_IN_ESP_PUSH_000 data byte 2 or 6 on zone 2101

All wires settings seem to be inside 2101 zone (IN & OUT)
 
Dernière édition:
  • J'aime
Reactions: marcins

[QUOTE = "Hallahub, post: 2614073, member: 114118"] Ora hai solo 4 sensori posteriori, se scambi l'ecu AAS con 6 + 6 uno e non ti connetti un totale di 12 sensori, vedere l'errore di assistenza al parcheggio sul cruscotto. La codifica manuale dell'AAS_UDS_gen6 (che è la centralina di parcheggio della nuova Peugeot 208/2008 opel corsa ecc.) Non è possibile, non c'è nemmeno un menu all'interno di diagbox per questo. Penso che se non aggiungi tutti i sensori extra il sistema non funzionerà.

modifica: hai solo 6 sensori posteriori, sei sicuro? Mi sembra strano. [/ QUOTE]

Ciao Hallahub, mi dispiace disturbarti di nuovo, non riesco a trovare un modo corretto per procedere con l'installazione dei miei sensori ... ora ho AAS 12x, telaio posteriore con 6 sensori, sto acquistando il telaio anteriore con 6 sensori, ma. .. ho bisogno di sapere se, una volta installato tutto, cosa devo fare davvero, riprogrammare solo BSI? come è possibile in una 2010-evo, magari usando qualche altro VIN di un'auto donatrice?
Non voglio installare tutto e perdere gli 8 sensori che ora funzionano bene, se non riesco a portare a termine il lavoro.
Grazie!
 


@VLud, Est-il possible dans un Traveler 2018 de désactiver le son émis lors de l'ouverture ou de la fermeture de la porte latérale automatique? Toute aide appréciera. (Sorry for my French)

English: Is it possible in a Traveller 2018 to disabled the sound made when automatic side door is opening or closing? Any help will appreciate
 


Bonjour, ma femme a un C4 Grand Picasso 2017 avec l'assistance au parc 360. Le problème est que chaque fois qu'elle engage la marche arrière, le système demande quelle vue afficher (comme dans la première photo ci-jointe), et c'est ennuyeux. Est-il possible que le NAC automatique affiche cette autre manière (avec vue d'oiseau et vue arrière - deuxième image)? Dois-je uniquement télécoder ou dois-je effectuer des modifications de connexion dans le faisceau de la caméra? Merci et désolé pour le pauvre français.


 

Bonjour, ma femme a un C4 Grand Picasso 2017 avec l'assistance au parc 360. Le problème est que chaque fois qu'elle engage la marche arrière, le système demande quelle vue afficher (comme dans la première photo ci-jointe), et c'est ennuyeux. Est-il possible que le NAC automatique affiche cette autre manière (avec vue d'oiseau et vue arrière - deuxième image)? Dois-je uniquement télécoder ou dois-je effectuer des modifications de connexion dans le faisceau de la caméra? Merci et désolé pour le pauvre français.


You need to duplicate the video signal from the instrument cluster to the nac
 
  • J'aime
Reactions: BR308

Hi guys! After upgrading from a NAC Wave 2 to a NAC Wave 4, i'm facing some issues.
Today I spent some time trying to figure out why the NAC is assuming there are obstacles in front and behind my vehicle, even if I'm in a open field and there is nothing around my car.
The point is: every time I engage the R gear, the Visiopark shows the zoom view and the virtual top view shows red alerts like if there are obstacles close to both bumpers.
I tried to restore the original config file, change the vehicle and compared the W2 and W4 backups but couldn't identify different parameters.
The BSI parameters are correctly set as if I reinstall the W2, the issue go away.
There are no errors on AAS or any BSI related module.
Anybody can think about something I'm missing or had similar issue?
Attached pictures and my W4 config file.

AAS_1 picture was shot while I was parked with any obstacles close to the car.
AAS_2 picture was shot immediately after AAS_1, but I switched the gear lever from R to N.
AAS_3 picture shows the 2 right sensors working properly (the front right yellow and rear right white alerts).
AAS_4 picture show the 2 center front and 2 center rear sensors not working properly.

Thanks.
 

Pièces jointes

  • AAS_1.jpeg
    AAS_1.jpeg
    86.8 Ko · Affichages: 84
  • AAS_2.jpeg
    AAS_2.jpeg
    117.2 Ko · Affichages: 81
  • AAS_3.jpeg
    AAS_3.jpeg
    96.7 Ko · Affichages: 79
  • AAS_4.jpeg
    AAS_4.jpeg
    73.1 Ko · Affichages: 77
  • NAC_W4.txt
    856 octets · Affichages: 17





hello friends, I need help again :(
tried to load on the cirocco 3008 the calibration 508 and configs now got black screen
I try to load the 3008 again but it is only there.
I already had this problem once and vlud solved it but now I'm not getting it.

log

> 00
< 7F0011

> >75F:65F
> 1003
< OK

> 00
< 7F0011

> >75F:65F
> 1003
< OK

< 7F1012

> 1002
< 5002

> 22F0FE
< 62F0FEFFFF000002FCFFFFFF00011100000000FDC7B7E301928014

> 22F080
< 62F080981051468000029825340980FFFFFFFF0001FFFFFFFF

> 22F18C
< 7F2231

> 1001
< 5001

> 1002
< 5002

> 2701
< 6701BFEC6007

> 27025D9F6FCF
< 6702

> 3101FF0081F05A
< 7101FF0001

> 3103FF00
< 7103FF0001

> 3103FF00
< 7103FF0002

> 3481110000
< 741000

> 3601FF000200433E307FC00FF5DC644480FA00086D14320000020305070A0E1319222E3D526D91C0FF05A80A141E28141E2832600005121F2C3946535F65A05600011388186A5080FE13A17A
< 76010A
Latest cirocco.exe app not works with load .cal/.ulp same problem here ...
 

hello friends, I need help again :(
tried to load on the cirocco 3008 the calibration 508 and configs now got black screen
I try to load the 3008 again but it is only there.
I already had this problem once and vlud solved it but now I'm not getting it.

log

> 00
< 7F0011

> >75F:65F
> 1003
< OK

> 00
< 7F0011

> >75F:65F
> 1003
< OK

< 7F1012

> 1002
< 5002

> 22F0FE
< 62F0FEFFFF000002FCFFFFFF00011100000000FDC7B7E301928014

> 22F080
< 62F080981051468000029825340980FFFFFFFF0001FFFFFFFF

> 22F18C
< 7F2231

> 1001
< 5001

> 1002
< 5002

> 2701
< 6701BFEC6007

> 27025D9F6FCF
< 6702

> 3101FF0081F05A
< 7101FF0001

> 3103FF00
< 7103FF0001

> 3103FF00
< 7103FF0002

> 3481110000
< 741000

> 3601FF000200433E307FC00FF5DC644480FA00086D14320000020305070A0E1319222E3D526D91C0FF05A80A141E28141E2832600005121F2C3946535F65A05600011388186A5080FE13A17A
< 76010A
Please send me calibration for 508 if u can, thank you!
 







Was nice to be here and help others how i can , but someone one talking bulshit that's im taking money for coding , and selling parts .... so please can this person have Own honour , come here and write this with proof ???? or will hide like dirty Rat. --let him fry in hell and his di*k no longer stands up for these lies---

As is easy like make shit , spok about someone do this ... and other things...
 
Dernière édition: