Contenu récent par jeverds

According to the latest version of Diagbox, there will be no OTA updates for any equipment at the moment, nor will they be available at dealerships except for unit replacements and with authorization from Stellantis at all times.

From what I've experienced, the instrument cluster in IVI systems is basically a screen for displaying the information generated by the IVI. This means that if we turn on a vehicle's instrument cluster with IVI, it doesn't display any image and only shows it when we connect it to the IVI. This...

Be careful with IVI integration. Regardless of the firmware version (NHW, AHW, KHW), they all store the mileage in zone D70A and transfer it to your BSI if it's higher than the mileage of the vehicle you want to integrate it into. If you plan to integrate an IVI, make sure it has less mileage...

This is all well and good, but it's all been discussed before and doesn't offer anything new. Besides, you're just repeating what a user on drive2.ru posted, who didn't even show the installation, coding, etc., of the IVI system. If you want to publish something, make it something new that...

You have to remove your screen and behind it will be your NAC unit. Remove the screws that hold it in place and take it out. On the back of the unit you will find a connector like the one in the photo. Disconnect your original cable and connect the one from the antenna you bought. Place the...

Open PyPSADiag, go to zones, then to INJ, and you'll have the CMM_VD56 file.

https://es.aliexpress.com/item/1005009121323291.html?spm=a2g0o.productlist.main.5.765dsFLdsFLd6c&algo_pvid=eefb8231-4121-4ee7-bd37-bb065142d4b9&algo_exp_id=eefb8231-4121-4ee7-bd37-bb065142d4b9-4&pdp_ext_f=%7B%22order%22%3A%224%22%2C%22eval%22%3A%221%22%2C%22fromPage%22%3A%22search%22%7D&pdp_npi=6...

If anyone is interested in a complete 2023 Peugeot 308/408 GT conversion kit NAC/IVI, please message me privately. Wiring and a rear camera are not included. I can include a dual CAN bus module.

If anyone is interested in a complete 2023 Peugeot 308 GT conversion kit, please message me privately. Wiring and a rear camera are not included. I can include a dual CAN bus module.

The IVI system cannot be updated by Stellantis services through the official DIAGBOX unless ordered by the manufacturer. If a vehicle with factory-installed IVI needs to have the system replaced, it will already be updated from the factory. If not, the manufacturer will provide instructions for...

The update system and app not only check the VIN, which of course will no longer be the same as the vehicle it was installed in, but also serial numbers, unit calibrations, etc. Therefore, even if you enter your BSI's VIN into IVI and BSRF, the system will still recognize the error. And since...

I can't tell you which version you'll find the IVI in for the 208, but as I said, you can use another car model for the diagnostic that has had both NAC and IVI. Version 9.186 is probably a bit outdated for this; I usually use the latest version, and I'm currently on 9.243. It's a matter of...

To access Diagbox, use a vehicle equipped with both NAC and IVI in the 2010EV BSI, such as a Peugeot Rifter. This will allow you to select the IVI, and from there you can verify the camera's functionality. You will need an updated version of Diagbox because, for example, the Peugeot Rifter only...

What camera model are you using? Have you checked it with Diagbox?

I can no longer help you with this because if the calibration that your IVI has for VISIOPARK is not compatible with your installation, you will not be able to do anything until these calibrations can be changed and as you can see, if someone has the knowledge, they do not want to share it.