Contenu récent par Kozioł

  1. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello in 508, I installed the 360 module and the front and rear cameras, the image from the camera on the screen is half the size
  2. K

    [TUTO] Adaptateur pour SMEG/NAC/Matrice CAN2010 sur BSI CAN2004

    Yes, this error, you need to add the command in arduino
  3. K

    [TUTO] Adaptateur pour SMEG/NAC/Matrice CAN2010 sur BSI CAN2004

    Hello, after installing the adapter and nac W3 on ds3, I have an engine error message with diagbox reading (No communication with the multifunction screen or with the telematics module). Where in the library it is necessary to switch to missing.
  4. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello Vlud, do you have a configuration for citroen c4 picasso
  5. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello, I need a configuration on a c4 picasso
  6. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I also confirm that it has been said well
  7. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello Vlud, thank you so much for your work. I installed in ds3.
  8. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello vlud I made a software update I have fmux on w4 to ds3 thank you very much. Marcins sent you my backup files, I couldn't add them.
  9. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello Vlud this is nac w3 not rcc, application 1,2,2 and sketch 1,5. I will add a backup later
  10. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    [GALERIA = media, 2073] AE7AEF59-8111-44A1-9419-2E8CC1706D33 autor: Kozioł opublikowano 8 lutego 2021 o 23:42 [/ GALLERY] Hello Vlud, after uploading 1.22 I also have no settings for w3 / w4 ds3
  11. K

    [TUTO] Adaptateur pour SMEG/NAC/Matrice CAN2010 sur BSI CAN2004

    V3nn3tj3, te przyciski można podłączyć do adaptera Vlud. Czy musi być dostępny drugi adapter sterowania przyciskiem? I czy przyciski są podłączona do ardiuno,
  12. K

    [TUTO] Adaptateur pour SMEG/NAC/Matrice CAN2010 sur BSI CAN2004

    Hello VLud I made an arduino adapter and 2 CAN-Bus Shield v2.0 cs9 cards are on top and connected to nac a cs 10 on the bottom and connected to bsi can ds3. Navi won't run black screen, that's something wrong
  13. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Hello VLud, where you need to change the meter or navi to set the dynamics in the Peugeot 3008.
  14. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    ok
  15. K

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    VLud and connection of menu and vol + - ds3 buttons
Voir plus
Haut Bas
Back