Contenu récent par nico1080

  1. N

    Lecteur OBD arduino

    Pour les gens qui serait intéressés j'ai fabriquer un lecteur a connecter sur la prise diag qui permet d'afficher plein d'info qui manque au tableau de bord (temperature d'eau, huile etc , pression des pneus) Tout est paramétrable a l'infini. Il y a plusieurs écran que l'on peux changer en...
  2. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    @VLud je rencontre un problème pour lancer l'outil nac ou cirocco: lorsque je fait "arduino connect" j'ai bien le bouton NAC/CMB access qui se déverrouille et quand je clique dessus les autres boutons n'apparaissent pas. J'ai tester avec 2 ordinateur et 2 connexions internet différentes...
  3. N

    [TUTO] Remplacer la caméra de recul 130° par la caméra panoramique 180° (Visiopark 1) sur 308

    Deux possibilités pour le BSI, -utiliser un diagbox 7.57 (offline) pour coder sur present camera panaroamique (menu dispo uniquement mode c4 picasso) -Utiliser l'arduino pour réécrire la zone D540 (@Albatros24 a déjà donné toute les infos pour le faire)
  4. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    @VLud , as @Futee it do not solve the problem, I tried again today both NAC/ Cirocco software do not work (I tried about 10 time for each software) In log file and in arduino serial monitor, I have Ok answer, so the issue is not with arduino.
  5. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I tried it several time each time same behavior with both back and cirocco software
  6. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    @VLud je pense qu'il y a un probleme avec les deux logiciel du NAC et du cirocco. Lors du lancement en cliqant sur NAC/CMB connect il ne se pass rien et dans le log, il y a juste: > 00 > >764:664 > 1003 < OK J'ai essayer avec les dernières versions sur le github et des anciennes: pareil
  7. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I have same setting execpt in 2129, video resolution 1 is disabled on resolution 2 is enabled. I put this setting when I installed NAC and did not change it when setting the cirocco.
  8. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I changed only these setting in NAC : 2110 sortie secondaire nav: sortie video pour NAV 2108 perso combiné (aparametre 212d icockpit amplify -(app) fait apparaitre menu 2126 theme combine (icokpit amlify) pas d’impact
  9. N

    Arduino Sketch for 308/3008/508 Digital Cluster Retrofit

    Pour les personnes intéressées, j'ai écrit un sketch Arduino qui permet de faire marcher les boutons de l'aide au stationnement et de la surveillance d'angle mort. Je l'ai testé sur DS4, mais il devrait fonctionner sur toutes les voitures BSI2010. https://github.com/nico1080/DS4-cirocco-retrofit
  10. N

    [TUTO] Remplacer la caméra de recul 130° par la caméra panoramique 180° (Visiopark 1) sur 308

    change the vehicle type in diagbox to vehicle that have visioaprk2, for exemple I have a ds4 and by chosing 3008, it scan all ECU available in 3008 and find visiopark2. ecu.
  11. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    There is no way to program an arduino that add the some of the missing function between BSI2010 and BSI2010-ev? (they are very close)
  12. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Another question regarding the speed limit sketch. On newer car, it is possible to set the cruise control to the speed limit by double press on the mem key. see video between 2min and 3min: Do you think it is possible to activate it on BSI 2010? On my side, I tried to activate the...
  13. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    Yes Arduino are reliable. (At home, I have some project that works for several year without any issues) But automotives environnements are harsh (vibration, temperature, etc) and OEM car electronic have much higher reliability standard than arduino. (especially if we compare Chinese clone with...
  14. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I don't like this method because in case of Arduino failure (software or hardware) no cluster at all. Is there anyway to prevent the BSI from sending the speed limit frame? Either by telecoding or by asking with a can message not to send?
  15. N

    [TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

    I have BSI q04-01 on Ds4 restyl (2016) The grey sign turned on as soon as I activated the speed limit display in cirocco. But your explanation of duplicate can frame make a lot of sense. :bien: Is there any workaround for that?