central lock ecu unit

[davor091]

hi again

can anyone tell me location of central lock ecu unit ,part nr:9648572680 on 607 2.7 hdi 2005, see pics
regards

(google translate
Re-bonjour

quelqu'un peut me dire l'emplacement de l'unité de l'écu central, partie n °: 9648572680 sur 607 2.7 hdi 2005, voir photos
Cordialement

 

[Oldwinuser]

Hi,

How do you know this CLE is the culprit ? In fact, what is your problem exactly?
And by the way, is English your native language and where are you from?

 

[davor091]

im from Croatia, my language is Croatian, central locking dont work and everyting else is fine, leads , diagnostic tool says CLE

 

[davor091]

heeelppp meeee

 

[Oldwinuser]

Hi,

OK, got it. The central locking don't work at all or just by using the remote ? What about the switch on the center armrest ?
Amis du forum, davor091 voudrait savoir où se trouve le boitier de la condamnation centralisée (avec l'antenne réceptrice je suppose), je n'en ai aucune idée mais je suis sur que certains d'entre-vous le savent.

 

[yann3]

le boitier est dans la porte conducteur

 

[yann3]

le 32

 

[davor091]

32 is this ?

 

[yann3]

c'est bizard
c'est un boitié Z8,donc phase 1 sur une 2.7 hdi,donc phase2

 

[yann3]

voila le recepteur Z8 de la ph1,qui se trouve sous la plage arriere

comme tu peut le voir,c'est le meme que ta photo

 

[davor091]

my problem is the fact next:
in car service the mechanic was wrong conect battery, car battery, no battery in the key, the car battery,dont ask me why and how,stupid,
and after that, the trunk button does not work (but it has been tested and work fine)
all wires are correct, door lock mechanism is tested on another car and working properly, fuses correct, flip motor work, I'm going crazy

 

[yann3]

we must rebuild a safe learning, if it is a 2.7 HDI
but it is surely not the calculator shows you a picture because Z8 therefore phase1

 

[davor091]

yes,i did try safe learning, but trunk doesnt work, all doors work, only trunk doesnt work.

 

[Oldwinuser]

Hi,

So, if everything works but the trunk, the problem must be with the trunk lock itself or with its motor.
I suppose it is an electric powered one and if so, if you push the "0" to open or red button to lock, what's going on ?

Merci Yann,

 

[davor091]

trunk lock mehanism dont work but i tested him on secodn car and work fine, when i press "O" nothing happens, but when i press inside red button ,the trunk will be close

 

[yann3]

So surely beam trunk hinge, cut, at the back beach

 

[captain bernard]

Probably something wrong concerning the coil trunk, or the knob "0" of 607 is finished. is the trunk lift up normaly by the remote? or not.
Is it a powered trunk?

 

[davor091]

Yes, trunk is powered
knob "o" :tested-ok
remote trunk dont work
all, i repeat ,all leads is fine,no cut

 

[davor091]

and this work when i tested him on second car

 

[captain bernard]

I think you have to re-learn by Peugeot procedure trunk. Like Windows as well, and all of automotive accessories. It exists a specific procedure for trunk propely step by step. I don't know it, because of mine is not powered. Try to reach a Peugeot dealer nearest you.
This forum contain that procedure, try to make a request in "recherche" section. in french: reprogrammation du coffre motorisé

 

[yann3]

il a deja la procedure
http://www.forum-peugeot.com/forum-peugeot/Peugeot-607/Questions-techniques-11/automatique-ouvert-probleme-sujet_39503_1.htm

 

[davor091]

is it possible to find scheme of of installation, complete car ??


est-il possible de trouver un schéma d'installation, voiture complète

 

[davor091]

s it possible to find scheme of of installation, complete car ??


est-il possible de trouver un schéma d'installation, voiture complète

 

[yann3]

Hello
Complete car diagram, not
but you can have the diagram for cable components

 

[yann3]

http://www.aht.li/2918146/http1270016092Sdrimprimer_coffre_v6_hdi.pdf

C001 = diagnostic socket
6222 = set lock case
6290 = safe maneuvering case
6289 = gache chest
6292 = Safety switch
PCF1 BSM =
BSI1 BSI =

 

[yann3]

check the fuse PF 3

 

[davor091]

thanks, i will

 

[davor091]

colors of leads maybe?

 

[yann3]

the wire are numbered and you have the number of connection catch

 

[davor091]

can you tell me location of: 6290 = safe maneuvering case


http://www.aht.li/2918146/http1270 [...] v6_hdi.pdf