Come on ... please. There are two parts in the soft, calibration and settings (parameters), you have to do both to make buttons work.
But if you have RT6 buttons don't expect them to work, you have to change the FMUX.
https://www.forum-peugeot.com/Forum...agbox-via-arduino.121767/page-48#post-2606524calibration AND configuration must be changed to make FMUX buttons working.
Hello, I would like to help with Slovak/Czech translation.
Multilingue avec changement instantané (pas comme Diagbox), commencement des menus des ECUs, ça avance !
Quand j'aurais fini toute la base et les structures des JSON je pourrais publier et c'est là que tout le monde pourra rentrer en jeu pour la traduction, l'ajout des voitures, l'ajout des ECUs, etc
Beaucoup de boulot où l'union fait la force et où toute personne qui aidera gagnera sa place en crédit
It's all written, just read the pages of this discussion carefullyMerhaba, öncelikle bu güzel konu için teşekkür ederim. Sorum şu, bu resimdeki menüyü nasıl etkinleştirebilirim. Teşekkürler.
@VLud tested and working perfectly. Thank you so muchCirocco app updated, added few more settings based on previous reviews, and fixed some wrong positions
Should allow you to upload the calib again @joan carlos
My settings are:
but a personal note: I have issues with the display not dimming. when i turn on the lights
Voir la pièce jointe 16885 Voir la pièce jointe 16886 Voir la pièce jointe 16887 Voir la pièce jointe 16888 Voir la pièce jointe 16889 Voir la pièce jointe 16890 Voir la pièce jointe 16891
Time after open diag session to this request need to be lower than 3 sec. Otherwise Session will automatically back to default Session 1001, and this make effect -> 7FF18C for 22F18C. Get Infor 22xxxx is not allowed in session 1001. Time reject You from 1003 session . You should work faster or use tester present msgi formatted my pc for windows 7 ultimate x64 and i have the same problem. it had happened to me before and it was just loading the calibration again. now with both libraries is that the arduino-cirocco gives an error and closes automatically. this list:
> 00
< 7F0011
> >75F:65F
> 1003
< OK
< 7F1012
> 1002
< 5002
> 22F0FE
< 62F0FEFFFF000002FCFFFFFF00011100000000FDC7B7E301928014
> 22F080
< 62F080981051468000029825340980FFFFFFFF0001FFFFFFFF
> 22F18C
< 7F2231
Chri208 did you maybe solved your issue with the 130 camera?Merci beaucoup... j'essaierai dès que j'aurai le temps
Welcome all,
I'm new to this forum and firstly I definitely need to admit how astonishing is the work done here and shared for free with the community! thx to Vlud a lot! It's definitely rare and we should really appreciate it.
I'm almost successfully switched from smeg to NAC wave2 in 508 sw, using manuals provided on this forum which is great!
However, I'm another guy having an issue with 130 degrees camera which doesn't show anything when reverse gear is on. It's just black screen with car sensors on the right side.
Obviously, I've checked all the pinsout of the smeg (B1,B7) - NAC (16,17) adapter and they are fine.
In Arduino, I have all options checked on page 2106, while on 2105 all are off which also should be the way to go.
I was wondering if there is a way, e.g. through Arduino to check if the signal from the camera is coming to NAC?
My NAC came from C3 aircross...
Chri208 did you maybe solved your issue with the 130 camera?
I'm civil engineer and wondering if there is a smarter way to fix it than just to use a hammer! So I highly appreciate any suggestion.
Yes, my 130 deg cam was working well with SMEG, thus I think it should be due to connection or NAC itselfYou have working CAM before with SMEG? when not there also need to be activated in BSI and AAS module