ESP? Havent seen any coding for it in the thread.
maybe this is missing. What should be changed here?Currently i dont have the car with me, but i will try to come back with the current values asap
[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino
- Démarrée par VLud
- Date de début
ESP? Havent seen any coding for it in the thread.
maybe this is missing. What should be changed here?Currently i dont have the car with me, but i will try to come back with the current values asap
For the ESP, it's these lines :
Codage de l'ESP :
>6AD:68D - Sélection de l'ESP (ABRASR) | OK
1003 | Ouverture du diag | 7F1078 / 500300C80014
222101 | 6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFDFFFFFFFFFFFF7FFFFFFFFFFDFFFFFFF7FFBFFEFDFDADEFF
-> Valeur lue = valeur à écrire = OK
Or i'm wrong ?
Codage de l'ESP :
>6AD:68D - Sélection de l'ESP (ABRASR) | OK
1003 | Ouverture du diag | 7F1078 / 500300C80014
222101 | 6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFDFFFFFFFFFFFF7FFFFFFFFFFDFFFFFFF7FFBFFEFDFDADEFF
-> Valeur lue = valeur à écrire = OK
Or i'm wrong ?
ESP cpk enabled
2E21010AFEFFFFFFFFFFFFFFFFFFFFFFFFDFFFFFFFFFFFF7FFFFFFFFFFDFFFFFFF7FFBFFEF9FDADEFF
DAE cpk enabled
2E210103CEF7EFFFFEFFFFFFFEFFFBFFFFFF
but again, things might be different depending on the car and some bytes should stay the same, right? Its not really copy paste
or is it?Sory, but here I can't help you. On my car these lights were activated by default.
May be, in BSI, the zone 236E The presence of outer side backlight enable these lights, but I'm not sure.
Also you should look in NAC.
that's in this particular esp/dae , other with differ size coding can have differ place ...but again, things might be different depending on the car and some bytes should stay the same, right? Its not really copy paste
ESP
Byte 38 bit 7.6
11xxxxxx -off
10xxxxxx -on
DAE
Byte 5 bit 0
xxxxxxx1 -off
xxxxxxx0 -on
Hello, I have an E2008 GT and I also want to activate the park assist. I have the 6 front and rear sensors, rear camera and blind spot detector.
According to Thomas-Lyon's manual, I have read my parameters and they barely resemble those obtained by him in his car and I don't know which ones to modify to make it work, I'm afraid of doing something that will damage the car.
You will know which are the correct parameters that I have to modify so that everything works correctly.
These are the codes obtained from my car:
BSI: 622230013
DAE: 62210103CFF7DFFFFEFFFFFFFEFFF7FFFFFF
Codificación AAS (AAS_UDS_G6): 62210111088408520D4A
Codificación ESP: 6221010AFEFFFFFFFFFEFFFFFFFFFFFFFFDFFFFFFFFFFFFFFFFFFFFFFDFFFFFFF7FFBFFEFDFDADEFF
According to Thomas-Lyon's manual, I have read my parameters and they barely resemble those obtained by him in his car and I don't know which ones to modify to make it work, I'm afraid of doing something that will damage the car.
You will know which are the correct parameters that I have to modify so that everything works correctly.
These are the codes obtained from my car:
BSI: 622230013
DAE: 62210103CFF7DFFFFEFFFFFFFEFFF7FFFFFF
Codificación AAS (AAS_UDS_G6): 62210111088408520D4A
Codificación ESP: 6221010AFEFFFFFFFFFEFFFFFFFFFFFFFFDFFFFFFFFFFFFFFFFFFFFFFDFFFFFFF7FFBFFEFDFDADEFF
That's Thomas example so when read is as UDS write also with UDS 2E other can be differ
I have an 208 p21 Latin America. I'm going to install the sensors and module and try. I hope it works.
I did that. Enabled that. And I did connect the pin 4 of each exterior mirror connector to pin 23 of the yellow conector (60pins) of the BSI. Like it's supposed to. No success. What am I missing?
Hello, what would be the codes to be able to modify the ESP Coding and DAE Coding?
ESP Coding:
>6AD:68D - ESP Selection (ABRASR) | okay
1003 | Opening the diag | 7F1078/500300C80014
222101 | 6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF7FFBFFEFDFDADEFF
-> Value read = value to write = OK
DAE encoding:
>6B5:695 - DAE Selection | okay
1003 - Opening Diagnostic Session | 500300C80014
222101 - Zone reading | 62210103CFF7EFFFFEFFFFFFFEFFFBFFFFFF
-> Value read = value to write = OK
And do we know which byte to modify in each section?
In Bsi:
622230013 is modified by 2E230033
AAS encoding (AAS_UDS_G6):
62210111077007450D4C is modified by 2E210115077007450D4C
ESP Coding:
6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF7FFBFFEFDFDADEFF is modified by 2E21010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFDFFFFFFFFFFFF7FFFFFFFFFFDFFFFFFF7FFBFFEF9FDADEFF.
DAE encoding:
62210103CFF7EFFFFEFFFFFFFEFFFBFFFFFF is modified by 2E210103CEF7EFFFFEFFFFFFFEFFFBFFFFFF
If any expert can help with a complete manual for the correct activation of park assist, it would be appreciated.
ESP Coding:
>6AD:68D - ESP Selection (ABRASR) | okay
1003 | Opening the diag | 7F1078/500300C80014
222101 | 6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF7FFBFFEFDFDADEFF
-> Value read = value to write = OK
DAE encoding:
>6B5:695 - DAE Selection | okay
1003 - Opening Diagnostic Session | 500300C80014
222101 - Zone reading | 62210103CFF7EFFFFEFFFFFFFEFFFBFFFFFF
-> Value read = value to write = OK
And do we know which byte to modify in each section?
In Bsi:
622230013 is modified by 2E230033
AAS encoding (AAS_UDS_G6):
62210111077007450D4C is modified by 2E210115077007450D4C
ESP Coding:
6221010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF7FFBFFEFDFDADEFF is modified by 2E21010AFEFFFFFFFFFFFFFFFFFFFFFFFFFFDFFFFFFFFFFFF7FFFFFFFFFFDFFFFFFF7FFBFFEF9FDADEFF.
DAE encoding:
62210103CFF7EFFFFEFFFFFFFEFFFBFFFFFF is modified by 2E210103CEF7EFFFFEFFFFFFFEFFFBFFFFFF
If any expert can help with a complete manual for the correct activation of park assist, it would be appreciated.
Pièces jointes
Hi, I have a Visteon instrument cluster and am attemping to change the airbag zone.
This is the output when entering 220200, is anyone able to suggest what I need to write back to enable passenger airbag on the LCD?
62020010000FF8001300088494FE006D00013200000000000000000000000000000000000000A814141E28141E28320000000000000000000000000000001388186A0002000000000A17232F3B47535F640000000000000000
This is the output when entering 220200, is anyone able to suggest what I need to write back to enable passenger airbag on the LCD?
62020010000FF8001300088494FE006D00013200000000000000000000000000000000000000A814141E28141E28320000000000000000000000000000001388186A0002000000000A17232F3B47535F640000000000000000
Just consider write what car etc what model of cluster as visteon is 4-5 type now on the market....
Hi
I upgraded my sound system with Helix M four DSP and aditional amps to full active system.
For now I switched to non amp mode and I am using a NAC volume control. But I plan to switch to multiplex to disconect volume control from standard amp and make my own can-bus-helix interface with arduino. (I alredy make it)
The problem is that when I switch to multiplexed system I loose signal of my parking sensor.
Enyone know how to configure a parking sensor sound on multiplexed system ?
I upgraded my sound system with Helix M four DSP and aditional amps to full active system.
For now I switched to non amp mode and I am using a NAC volume control. But I plan to switch to multiplex to disconect volume control from standard amp and make my own can-bus-helix interface with arduino. (I alredy make it)
The problem is that when I switch to multiplexed system I loose signal of my parking sensor.
Enyone know how to configure a parking sensor sound on multiplexed system ?
Multiplexed use only front output for amp and rear is disabled that's why no sound for parking sensor , need activate sound from COM for parking sensor in bsi...
What you mean enable passenger airgab? this is active from factory and you don't see it until not deploy...
The warning icon, not the airbag itself.What you mean enable passenger airgab? this is active from factory and you don't see it until not deploy...
You'd previously written this for the Magneti Marelli, I was wondering if the same could be achieved on Visteon?
For airbag zone 0200
byte 16
08=LED_plate
10=TFT
00= absent
I'm trying to retrofit a 308 display to a 208. 308 does not have passenger airbag light on the instrument cluster by default, instead it's on the seatbelt matrix next to the rear view mirror.
Is it possible to add the icon to the TFT, or am I best going for a screen from a C4 Picasso which often have the airbag warning icon configured already?
In multiplex system you can use AAS sounds from COM2008, in BSI zone 2302, set the zone to 01
Would you mind sharing about your DSP control system? I cant decide between have an analog amplifier or a DSP, with your control system I might be able to connect and control a DSP just like yours..
Discussions similaires
