[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

[DW10C]

Hi all. I'm having trouble using this on can2004 c5 x7. I have used first in can2010ev uds, c4 picasso b78 2017 without problems, both for reading and writing in uds ecus.

I am using sketch arduino-psa-diag on a Arduino Nano and MCP2515.

However, I can't use it properly in Citroen C5 X7 ecus CAN2004 (KWP2000).

For example, on bta_2 kwp2000, I can establish communication with it, I can read zones, but however, writing is not possible. In fact, ss soon as I send the unlock command I receive this response "7F2712" and I don't know what I'm doing wrong.

I have tried for example on other ecu bsi04ev and the same thing happens, I can read zones, but it is impossible to unlock ecu in order to be able to write later.

I'm using this for BTA_2.

>77C:67C
10C0
: DC3B:83:C0

And for bsi i am using this:

>752:652
10C0
:B001:83:C0

What should I do?

Regards

 

[shapala]

Момчета...Направих го!

Асистент за дълги светлини (HBA), Разпознаване на пътни знаци и навигация (SLI/ISA), Асистент за предупреждение на водача (DAA3), Асистент за поддържане на лентата (LKA), Предупреждение за напускане на лентата (AFIL)

Просто следвайте приложените параметри.

Voir la pièce jointe 32744

Voir la pièce jointe 32745

Големи благодарности на всички, които публикуваха информацията малко по малко на огромния брой страници тук, и специално на @VLud и @bagou91 за споделянето на техните страхотни инструменти

Hello, can you tell me for what are this zones in BSI:
D535
D524
D536
242F
244C
and this zone in CVM_2:
2100

 

[Dunno]

+u

Hello.
It isn't a lie, if I told you I've searched all internet to solve this problem.
I bought and RCC radio (9833500080) and display from C3 Aircross (propably). Everything is OK, I can change VIN, but problem the problem is when I want to change calibration to 308 T9 ( 308_T9-9692810980.cal ). When I upload it it download and then ZL FLASH ERASING ERROR ( Picture nr 1) .
Voir la pièce jointe 39177
When I try diffrent calibration ( diffrent to 308 or to diffrent car) it's saying Calibration file Invalid, but sometimes is everything okay and the calibration will update without problem ( 5008_P87E-9693020580 ). Have someone had identical problem? Can you please help me?

+Up

 

[Sn0wflakes]

Bonjour a tous !

Pour une 208 de 2018 GTLINE les branchements :
CAN H -> PIN 6
CAN L -> PIN 14

c’est bien ça ?

 

[chunchai]

Hello, can you tell me for what are this zones in BSI:
D535
D524
D536
242F
244C
and this zone in CVM_2:
2100

BSI
D535 :CODE UCE CAN CAFR (Commutateur Automatique Feux de croisement Feux de Route) - Smart Beam
D524 :CODE UCE CAN Capteur Angle Volant (CAV)
D536: CODE UCE CAN Camera Multi Fonction (CMF) - Camera Video Multi Fontion (CVM)
242F : Option liant LKA et BSD
244C: Type de Lane Assist
CVM2
2100: Gauging group data values

 

[shapala]

Hi all, I activated"welcome to driver" function and now when stop the car and open the door my seat move back, but after when come back to the car and close the door, start engine, my seat doesn't go back to memorized position. Some time is go, but only when time between stop and start are very short. Is this normal or must change something?

 

[jeverds]

Bonjour a tous !

Pour une 208 de 2018 GTLINE les branchements :
CAN H -> PIN 6
CAN L -> PIN 14

c’est bien ça ?

If they are in the OBD connector yes
If it is for connection with Arduino, they would be the 3 H and the 8 L

 

[markgonzalez]

Bonjour a tous !

Pour une 208 de 2018 GTLINE les branchements :
CAN H -> PIN 6
CAN L -> PIN 14

c’est bien ça ?

C'est plutôt
CAN H -> PIN 3
CAN L -> PIN 8

 

[Sn0wflakes]

Je souhaite brancher les 2 fils uniquement sur le côté de larduino (CAN H & CAN L) sans passer par la prise qui sert pr l’OBD
Et quand je fais des recherches pour la 208 ils mettent :
CAN H -> PIN 6
CAN L -> PIN 14
Je comprends pas pourquoi ?

 

[chunchai]

Hi all, I activated "welcome to driver" function and now when stop the car and open the door my seat move back, but after when come back to the car and close the door, start engine, my seat doesn't go back to memorized position. Some time is go, but only when time between stop and start are very short. Is this normal or must change something?

I thought it may be a system bug, my friend has the same issue happened. I had once.

 

[shapala]

I thought it may be a system bug, my friend has the same issue happened. I had once.

Are there any solution for this bug?

 

[DW10C]

Are there any solution for this bug?

Telechargement bsi = new calibration

 

[shapala]

Telechargement bsi = new calibration

What is this mean? I must have token and update my BSI or what?

 

[jeverds]

Je souhaite brancher les 2 fils uniquement sur le côté de larduino (CAN H & CAN L) sans passer par la prise qui sert pr l’OBD
Et quand je fais des recherches pour la 208 ils mettent :
CAN H -> PIN 6
CAN L -> PIN 14
Je comprends pas pourquoi ?

Please explain a little more what you want to do.
The CAN line connections you indicate are those found in the vehicle's OBD connector, but to connect an Arduino and modify things using the instructions on the VLUD page or this forum, you have to use pins 8 and 3 of the OBD connector as shown in the photo I posted. If what you want is something else, please explain it better so we can see if we can help you.

Explique un peu plus ce que tu veux faire.
Les connexions de ligne CAN que vous indiquez sont celles que l'on retrouve dans le connecteur OBD du véhicule, mais pour connecter un Arduino et modifier les choses en suivant les instructions de la page VLUD ou de ce forum il faut utiliser les broches 8 et 3 du connecteur OBD comme Montrer la photo Je t'ai donné. Si ce que vous voulez est autre chose, expliquez-le mieux pour voir si nous pouvons vous aider.

 

[chunchai]

What is this mean? I must have token and update my BSI or what?

I think he is meaning that you can use arduino tools to set BSI 234C again.
01->00->01

FYI,hope it could help you

 

[Sn0wflakes]

Please explain a little more what you want to do.
The CAN line connections you indicate are those found in the vehicle's OBD connector, but to connect an Arduino and modify things using the instructions on the VLUD page or this forum, you have to use pins 8 and 3 of the OBD connector as shown in the photo I posted. If what you want is something else, please explain it better so we can see if we can help you.

Explique un peu plus ce que tu veux faire.
Les connexions de ligne CAN que vous indiquez sont celles que l'on retrouve dans le connecteur OBD du véhicule, mais pour connecter un Arduino et modifier les choses en suivant les instructions de la page VLUD ou de ce forum il faut utiliser les broches 8 et 3 du connecteur OBD comme Montrer la photo Je t'ai donné. Si ce que vous voulez est autre chose, expliquez-le mieux pour voir si nous pouvons vous aider.

Hi Jeverds!
Thank you for helping I’m new on this and a bit scared as it’s my first time
I ordered Elegoo R3 Uno + CAN BUS Shield 2.0
I plugged them on my pc and successfully launched the sketch. Changed the number 10 to 9 as mentioned in the tuto as I have a 2.0 shield
I compiled it and uploaded it to the Arduino

Now everything is ready and from what I understood I have to plug 2 wires on the side of the Arduino (CAN H & CAN L) and plug them in the OBD plug of the car
As I have a 208 2018 model I checked what are the pins on the car on google and it shows
Pin 6 and 14

My radio was stolen I bought a new one and it’s bipping
So if you could tell how to do

 

[jeverds]

Hi Jeverds!
Thank you for helping I’m new on this and a bit scared as it’s my first time
I ordered Elegoo R3 Uno + CAN BUS Shield 2.0
I plugged them on my pc and successfully launched the sketch. Changed the number 10 to 9 as mentioned in the tuto as I have a 2.0 shield
I compiled it and uploaded it to the Arduino

Now everything is ready and from what I understood I have to plug 2 wires on the side of the Arduino (CAN H & CAN L) and plug them in the OBD plug of the car
As I have a 208 2018 model I checked what are the pins on the car on google and it shows
Pin 6 and 14

My radio was stolen I bought a new one and it’s bipping
So if you could tell how to do

Comme je l'ai indiqué dans les messages précédents, vous devez les connecter aux broches 3 et 8 de votre connecteur OBD, mais vous feriez mieux de regarder ici toutes les informations, c'est là qu'elles vous l'expliquent le mieux car ce qu'elles vous disent sur Google sont ne pas utiliser avec le croquis VLUD.
Ici vous avez toutes les informations.

[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

As I indicated in the previous messages, you have to connect them to pins 3 and 8 of your OBD connector, but it is better to look here for all the information, which is where it is best explained because what you are told on Google is not for use with the VLUD sketch.
Here you have all the information.

[TUTO] Télécodage et calibration d'un NAC / RCC / CIROCCO / CMB_NUM SANS Diagbox via Arduino

 

[Sn0wflakes]

Alright, I will connect 2 wires on the Arduino and plug them on the pin 3 and 8

I will update in few days if it did work

 

[gusao10]

INGLÊS
Bom dia a todos.
Eu tenho um Peugeot Rifter 2019 SEM controle de aderência SEM controle de descida.
Eu tenho um controle de aderência + controle de descida Peugeot Rifter 2024 SI.
RIFTER 2019 ESP90 marca BOSCH.
RIFTER 2024 ESP90 marca BOSCH.

RIFTER 2019 ZONA 2101 ESP 62210106FBFFFFFFFFFFFFFFFFFFFFFFFFFFFBFFFF77FFFFBFFFEEFBA6EFF

RIFTER 2024 ZONA 2101 ESP 6221010AFFFFFFFFFFFF7FFFFFFFFFFFFFBFFFFFFFFFFFFFFFFBFFFFFFFF7FFFFFFEFFBFFEFDD5A6EFF

Minha dúvida é: posso utilizar os valores da zona 2101 RIFTER 2024 para ativar o controle de aderência e controle de descida no RIFTER 2019.
Se a resposta for não, quais valores teriam que ser alterados na zona 2101 do RIFTER 2019 para poder ativar essas duas funções.

A DIAGBOX indica nos 2019 e 2024 que possuem ESP90 mas ao identificar o aparelho no seu interior diz que é da marca BOSCH. Isso está correto e, em caso afirmativo, qual chave de desbloqueio devo usar?
aqueles de ESP90:60A5:03:03/:BC93:03:03.
o BOSCH:FFFF:03:03.
Desculpe pela tradução, espero que tenha sido compreendido.


FRANCÊS
Olá pessoal.
Eu tenho um Peugeot Rifter 2019 SEM controle de tração SEM controle de descida.
Eu tenho um controle de aderência + controle de descida Peugeot Rifter 2024 SI.
Marca BOSCH RIFTER 2019 ESP90.
RIFTER 2024 ESP90 da BOSCH.

RIFTER 2019 ZONA 2101 ESP 62210106FBFFFFFFFFFFFFFFFFFFFFFFFFFFFBFFFF77FFFFBFFFEFBA6EFF

RIFTER 2024 ZONA 2101 ESP 6221010AFFFFFFFFFFFFFF7FFFFFFFFFFFFFBFFFFFFFFFFFFFFFBFFFFFFFF7FFFFFFEFFBFFEFDD5A6EFF

Minha dúvida é: posso usar os valores da zona 2101 RIFTER 2024 para habilitar o controle de aderência e controle de descida no RIFTER 2019.
Se a resposta for não, quais valores precisariam ser modificados na zona 2101 do RIFTER 2019 para poder ativar essas duas funções.

A DIAGBOX indica nos de 2019 e 2024 que possuem o ESP90 mas ao identificar o aparelho no seu interior indica que se trata de uma marca BOSCH. Isso está correto e, em caso afirmativo, qual chave de desbloqueio devo usar?
aqueles do ESP90:60A5:03:03/:BC93:03:03.
o de BOSCH:FFFF:03:03.
Desculpe pela tradução, espero que tenha sido compreendido.

2E210106FBFFFFFFFFFFFFFFFFFFFFFFFFFFFBFFFF77FFFFBFFFFEEE3A6EFF com controle de tração controle de descida, acredito que seria esse código, não tenho certeza, mas você pode testar.

 

[gusao10]

Olá. Você fez isso via arduino? Quero codificar o ESP para ativar o ACC. Mas não sei qual zona está relacionada ao ACC. Pode me ajudar?

I made an Excel spreadsheet where you can choose what you want to activate and deactivate in ESP and it shows you the result of what you chose. I did it for the 3008 II, I don't know if it works for everyone. If you want to test, follow the attached spreadsheet

 

[shapala]

I made an Excel spreadsheet where you can choose what you want to activate and deactivate in ESP and it shows you the result of what you chose. I did it for the 3008 II, I don't know if it works for everyone. If you want to test, follow the attached spreadsheet

Sorry, but I can not understand your sheet, for example if I want to active ACC, with semi-automatic parking system, with descent control and with automatic braking on risk of collision, how will be look my code and how will use your sheet?

 

[bilalemint]

I made an Excel spreadsheet where you can choose what you want to activate and deactivate in ESP and it shows you the result of what you chose. I did it for the 3008 II, I don't know if it works for everyone. If you want to test, follow the attached spreadsheet

Thank you very much for your work. It was very useful. If you want to do this for other ECUs, I can help you.

 

[disel]

Hello. Can you please help me? I can't turn on automatic light (HBA) in my cvm2 camera. 2E2100BC40 doesn't work. Maybe I need another command 2E2100???? ? Or do I need to change the software in my camera? Maybe you know how?

 

[bilalemint]

Hello. Can you please help me? I can't turn on automatic light (HBA) in my cvm2 camera. 2E2100BC40 doesn't work. Maybe I need another command 2E2100???? ? Or do I need to change the software in my camera? Maybe you know how?Voir la pièce jointe 39263

You have to activate it in BSI Also.

 

[ygorigor]

Hello.
Is anyone known how to fix this DTC?

 

[jeverds]

2E210106FBFFFFFFFFFFFFFFFFFFFFFFFFFFFBFFFF77FFFFBFFFFEEE3A6EFF com controle de tração controle de descida, acredito que seria esse código, não tenho certeza, mas você pode testar.

My original zone 2101 62210106FBFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFBFFFF77FFFFBFFFFEEFBA6EFF

2 CFG_000_FREIN_UCPR_CITY_PARK (CFG_000_FREIN_UCPR_CITY_PARK) EF
: Without semi-automatic parking system
: With steering wheel angle sensor U+ 3
: 2 CAN
: Without traction control

3 CFG_000_FREIN_UDS_UCPR_HADC (CFG_000_FREIN_UDS_UCPR_HADC) BA
: Without descent control system
: With automatic braking on risk of collision U+ ( with multifunction video camera only )
: Left-hand drive
: Wheel speed sensor with detection of the direction of rotation of the wheel
: Without automatic gearbox electric control ECU
: With hill start assistance system


In your EXCEL file, these are the options to get the EF bit at number 2, which indicates that the vehicle will be without semi-automatic parking assistance. However, this is not correct in my vehicle with EF in zone 2101 and if there is semi-automatic parking there may be an error in EXCEL.

Dans votre fichier EXCEL, voici les options pour obtenir le bit EF au numéro 2, qui indique que le véhicule se retrouvera sans aide au stationnement semi-automatique. Cependant, cela n'est pas correct dans mon véhicule avec EF dans la zone 2101 et s'il y a un stationnement semi-automatique il peut y avoir une erreur dans EXCEL.

In bit 3 it indicates that I do not have an automatic transmission controlled by ECU when in fact I have EATN8

Au bit 3 cela indique que je n'ai pas de transmission automatique contrôlée par le calculateur alors qu'en réalité j'ai EATN8

 

[disel]

You have to activate it in BSI Also.

Yes, I have activated everywhere. but I can't activate the HBA item in the cvm. I think my camera's software doesn't support this. if so, how do I change the software in the cvm?

 

[Jbs68]

Bon, j'ai enfin "rangé" mon arduino uno et sa carte CAN-BUS Shield
Pas mécontent du résultat

 

[markgonzalez]

Wow, c'est vraiment propre. C'est fait avec une imprimante 3D?

 

[Jbs68]

Wow, c'est vraiment propre. C'est fait avec une imprimante 3D?

Oui! Sur une bambu lab X1