On my 508 work with cal. But with start switch off, I not try with ulpload .cal not works on cirocco (invalid checksum) don't try load .ulp as will stuck with half brick screen
small .cal you can read and write manualy
220200
220201
etc
On my 508 work with cal. But with start switch off, I not try with ulpload .cal not works on cirocco (invalid checksum) don't try load .ulp as will stuck with half brick screen
small .cal you can read and write manualy
220200
220201
etc
I can load without problems, the problem is that it takes a long time to load.load .cal not works on cirocco (invalid checksum) don't try load .ulp as will stuck with half brick screen
small .cal you can read and write manualy
220200
220201
etc
oui, le logiciel est fait pour ce type d'opération.très bon boulot les gars je viens de récupérer une Peugeot 208 ANNÉE 2020 mais malheureusement elles est pas équiper de la camera de recul ,et je voudrais bien l installer ,ma question est si je peux l a activer
via Arduino . merci
Hello. Did you manage to make a 3d Cirocco model for c4b7?thanks!
I’ll try to create models for C4B7.
U SEARCH IN WRONG PLACE!j arrive pas a trouver le bsi dans la liste des Ecu
Abi Selamın aleyküm benim aracım 2021 3008 allure. Kendim gt line tema yüklemek istiyorum nasıl yapılıyor neler yapmam gerektiğini anlatabilirmisin lütfen rica etsem.Thank you very much for your sharing, dear VLud. I connected with db9-obd pins according to the link you shared. My car is using a 2019 model peugeot 3008 gtline copper theme right now. I do not have a red theme on my car. How can I enable it. I made a backup of the parameter file. How can I activate watching video in motion.
try "> 764:664" without quotesBon,
je viens d'essayer avec 2 cables directs vers la prise OBD2 de mon 5008, et bien j'ai l'erreur 7F0000 après la commande "764:664", d'ailleurs j'ai le meme souci (sans meme être branché à la voiture), donc souci de montage ?
je n'ai aucune soudure mais des cables F-F entre les 2 cartes
j'ai un jumper J1, placé en 8MHz et place 9 pour la partie CS_PIN_CAN0
#define SKETCH_VERSION "1.6"
#define CAN_RCV_BUFFER 40
#define CAN_DEFAULT_DELAY 5 // Delay between multiframes
#define MAX_DATA_LENGTH 512
#define CS_PIN_CAN0 9
#define SERIAL_SPEED 115200
#define CAN_SPEED CAN_500KBPS // Diagnostic CAN bus - High Speed
#define CAN_FREQ MCP_8MHZ // Switch to 8MHZ if you have a 8Mhz module
une idée pour trouver la solution ?
Photo de mon montage
Voir la pièce jointe 21487
from your pics looks like you conected CS from mcp to D10 arduino nano , se you need setup in sketchBon,
je viens d'essayer avec 2 cables directs vers la prise OBD2 de mon 5008, et bien j'ai l'erreur 7F0000 après la commande "764:664", d'ailleurs j'ai le meme souci (sans meme être branché à la voiture), donc souci de montage ?
je n'ai aucune soudure mais des cables F-F entre les 2 cartes
j'ai un jumper J1, placé en 8MHz et place 9 pour la partie CS_PIN_CAN0
#define SKETCH_VERSION "1.6"
#define CAN_RCV_BUFFER 40
#define CAN_DEFAULT_DELAY 5 // Delay between multiframes
#define MAX_DATA_LENGTH 512
#define CS_PIN_CAN0 9
#define SERIAL_SPEED 115200
#define CAN_SPEED CAN_500KBPS // Diagnostic CAN bus - High Speed
#define CAN_FREQ MCP_8MHZ // Switch to 8MHZ if you have a 8Mhz module
une idée pour trouver la solution ?
Photo de mon montage
Voir la pièce jointe 21487
Guys anyone that know this?Hello guys i have a 208 GT Line with tomtom Navi 10in screen, i was wondering if it was possible in someway to hide or remove the two bar at the sides of the screen, like i'd like to use android auto on full screen, but there are these damn sidebars!!
@tous, pourquoi mon Antivirus détecte un trojan dans le fichier PSA....exe ?
Un réel souci il faut en avoir peur ou c'est une erreur de classification de certain AV ?
the mcp is 8MHz not 16@marcins , i changed my cabling to your exact picture => now, my cabling is similar
@Miguel Angel , i changed also my sketch to :
#define CS_PIN_CAN0 10
#define CAN_FREQ MCP_16MHZ
remove the jumper J1 (remove blue cable)
but always the error with 7F0000 (the quote in my first message it's juste for the message not include when i write into the IDE)
Voir la pièce jointe 21514